I can't boot Windows 2000

  • Thread starter Thread starter TBLUHP
  • Start date Start date
Re: I can't boot Windows 2000

TBLUHP wrote:
> I get this message all the time what should I do?
> http://flickr.com/photos/20903619@N00/2200944221/

Boot with the Windows 2000 CD and launch the Recovery Console
then run these commands:

chkdsk /r

then do: fixboot

Be warned that there is always a risk of data loss when you run chkdsk
on a disk.

If it isn't too much to ask, may I ask how did you capture the BSOD?
Which tools/software did you use to capture this? If it's a digital
photo then you did a good job with the photo!

John
 
Re: I can't boot Windows 2000

This article may help.

http://support.microsoft.com/kb/822052/en-us

Also try creating a boot disk. For the floppy to successfully boot Windows
2000 the disk must contain the "NT" boot sector. Format a diskette (on a
Windows 2000 machine, not a DOS/Win9x, so the NT boot sector gets written to
the floppy), and copy Windows 2000 versions of ntldr, ntdetect.com, and
boot.ini to it. Edit the boot.ini to give it a correct ARC path for the
machine you wish to boot. Below is an example of boot.ini. The default is to
start the operating system located on the first partition of the primary or
first drive (drive0). Then drive0 partition 2 and so on.

[boot loader]
timeout=10
default=multi(0)disk(0)rdisk(0)partition(1)\WINNT
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINNT="Windows 2000 0,1"
multi(0)disk(0)rdisk(0)partition(2)\WINNT="Windows 2000 0,2"
multi(0)disk(0)rdisk(1)partition(1)\WINNT="Windows 2000 1,1"
multi(0)disk(0)rdisk(1)partition(2)\WINNT="Windows 2000 1,2"

Another possibility is to try loading the controller driver also from
floppy. For the floppy to successfully boot Windows 2000 the disk must
contain the "NT" boot sector. Format a diskette (on a Windows 2000 machine,
not a DOS/Win9x, so the "NT" boot sector gets written to the floppy), then
copy ntldr, ntdetect.com, and boot.ini to it. Edit the boot.ini to give it a
correct ARC path for the machine you wish to boot.

In order for this to work you'll want to change the arc path in boot.ini
from multi syntax to scsi syntax to indicate that Windows 2000 will load a
boot device driver and use that driver to access the boot partition. Then
also copy the correct manufacturer SCSI, or ultra DMA, or ATA100, or raid,
or serial ATA driver to the floppy but renamed to ntbootdd.sys

Something like this below;

[boot loader]
timeout=10
default=scsi(0)disk(0)rdisk(0)partition(1)\winnt
[operating systems]
scsi(0)disk(0)rdisk(0)partition(1)\WINNT="Windows 2000 0,1"
scsi(0)disk(0)rdisk(0)partition(2)\WINNT="Windows 2000 0,2"
scsi(0)disk(1)rdisk(0)partition(1)\WINNT="Windows 2000 1,1"
scsi(0)disk(1)rdisk(0)partition(2)\WINNT="Windows 2000 1,2"


--

Regards,

Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft Certified Professional
Microsoft MVP [Windows]
http://www.microsoft.com/protect

"TBLUHP" wrote:
>I get this message all the time what should I do?
> http://flickr.com/photos/20903619@N00/2200944221/
>
 
Back
Top